Macquarie Semiconductor and Technology on behalf of Micron Technology Taiwan, Inc. (F11)

Tokyo Electron Ltd. (TEL) Telius SP-305 SCCM

Asset ID: 12379

Print spec sheet

Tokyo Electron Ltd. (TEL)

Telius SP-305 SCCM

Dielectric Etch

Etch/Ash/Clean - Plasma Processing

Equipment details:

Date of Manufacture: 2008

Currently Configured for: 300mm

Current Equipment Status: Available

Asset HDD not included

Location of Equipment: Taoyuan, Taiwan

Available date: Currently Available

Process: OX

Tool config is based on original PO, please verify tool details at tool inspection

Standard Specifications

Software Revision: Linux 5.75 Rev 001

Lot Stability Dummy SW: Software for running lot stability wafer.

OEE WPH Software: Yes

GEM SEC Revision: TBD

Wafer Size: Diameter 300+/- 0.20mm(SEMI M1.15), Notch

Carrier: FOUP (Comply with SEMI E47.1 (25wafers))

Inter Face: 5 carrier stage (Continuous flow operation) with Semi compliant MENV and FIMS assemblies

Online Connection: GEM / CIM GJG (Hardware Interface : Ethernet 100Base-Tx)

Interface A: Yes

Utility Box: Regulator : Air/AR2500(SMC), N2/SQ-420E(VERIFLO), He/SQMICRO(VERIFLO)

Utility Box: Manual Valve : OGD20V-6RM-K / OGD10V-4RM-K (CKD)

Utility Box: Pressure Gauge : Bourdon Gauge

Loader Mod Corrosion Prevent: NO, without Corrosion Prevent

Load Lock Pressure Monitor: Pressure Switch : VSA100A (INFICON)

Load Lock Pressure Monitor: Pirani gauge : TTR211S LEYBOLD)

Load Lock Pressure Monitor: CM : 626A01TDE (MKS)

Maintenance Monitor: 2 (Flat Panel Display Touch Screen Type)

Water Leak Detector: 5 (LM;1, each PS;1)

Signal Tower: Red/Yellow/Green/Blue (Upper Left of Front x1 & Upper right section of loader on maintenance side x1)

Data Back up: USB& MO

EMO: Front x3, Rear x6

Cable Length: One 15m and one 16m (Interconnection, RF cables)

Inter Locks: External (When the I/L signal is received from Factory, gas valves are closed)

Fittings: No brass fittings

Supporting Remote Units

Chiller: UBRPD5A-2T?

Coolant: Lower:FC3283, Upper:FC40

Chiller Hose: BRINE HOSE 15/14M

Handy Maintenance Controller: LCD DISPLAY UT3-TLN21-A

RF Generator TOP: AGA-50B2

RF Matcher TOP: AMN-50B2

RF Generator Bottom: WGA-50E

Matching Controller: WMN-50H6(2MHZ/5KW)(PS3)

Pen Record Box: 2L80-00212-12

Loader Module: SELME2112ZS22-AD5

LOAD PORT: NO,Bolts-L type



Carrier ID Reader: NO,V640series+V700-L22 (Omron)

APC: 12 INCH (320MM)

Hardware Configuration

Proc Chbr 1,2,3,4: SCCM Oxide; Y203 Coating

Chamber hardware: FCC

Endpoint type: SE2000ii

ESC type: Ceramics ESCwith STD Vpp

Focus ring: 3.4mm

Thunderwall He Gas Inlet: Ceramic Thunderwall with Ceramic pusher pins

Polished focus ring: O

FC lower insulator: FC lower insulator w/quartz upper ring shield

Magnet Shield: O

Oring for Chbr Body-Depos: Armorcrystal, Chemraz SC657

CEL Body ASSY: Brine Control Mode


TMP Back Pressure Monitor: 51A11TGA2BA003 (MKS)

Dry Pump: ESR80WN, KEG approved

Final Valve, Heater: Valve; AGD21V-6RM-GWL4 (CKD)

Filter: Filter; CEP-TM_HL-VR-03PB (Toshiba Ceramic)

APC: Pendulum Motion Dia., 320mm(VAT), R.T.~90deg

Pressure Monitor: C/M (Process Monitor) : 627BRETDD2P (MKS), 45deg, 30Pa

Pressure Monitor: C/M (Self Check) : 627B11TDC2P (MKS), 45deg, 1330Pa

Pressure Monitor: B.A. Gauge (CM Calibration) : BPG400 (INFICON), 2.0x10-5 ~ 0.1Pa

Pressure Monitor: N,41A13DGA2AA040 (MKS), no process impact

Pressure Monitor: Pressure Switch : 51A11TGA2BA010 (MKS), H2/fluoro gas

Gas Box Configuration

Gas line 1- N2 1000 sccm-AERA FCD985CT-BF

Gas line 2- C4F8 200 sccm-AERA FC-D985CT-BF

Gas line 3- Ar 2000 sccm-AERA FC-D985CT-BF

Gas line 4- O2 50 sccm-AERA FC-D985CT-BF

Gas line 5- CH2F2 30 sccm-AERA FC-D985CT-BF

Gas line 6- CHF3 200 sccm-AERA FC-D985CT-BF

Gas line 7- CF4 200 sccm-AERA FC-D985CT-BF

Gas line 8- C4F8 50 sccms-AERA FC-D985CT-BF

Gas line 9- C3F8 50 sccms-AERA FC-D985CT-BF

Gas line 10- C4F6 50 sccm-AERA FC-D985CT-BF

Gas line 11- O2 1000 sccm-AERA FC-D985CT-BF

Gas line 12- Ar 500 sccm-AERA FC-D985CT-BF

Purge: N2 (Process Grade N2)

Filter: CNF1004USG4 (Nihon Pall)


Filter (N2): CNF1004USG4 (Nihon Pall)

Valve: Primary side(Utility-MFC):Mega mini (FUJIKIN)

Valve: Secondary side(MFC-PC):Mega one (FUJIKIN)

Piping: Dual Piping (for Gas leak containment, Gas box to Final valve & Exhaust through Gas box)

Gas Leak Detection Port: 5 Ports (6.35mm, Swagelok L-type)

Final Pressure Switch: 51A (MKS)

Pressure Gauge: Bourdon

Damage/Missing parts list

Please inspect tool to reconfirm

Dry pumps and customer provided items not included on sales

Enquire about this product

I agree to receive further communication from Macquarie Group Limited in accordance with its Privacy Policy, as amended from time to time.

Product Images

The information referenced on this page is accurate to the best of our knowledge. We do not warrant the completeness or accuracy of the information contained herein. Interested parties are encouraged to request inspection to verify equipment condition, configuration, and completeness. Any offer to purchase equipment shall be subject to our standard terms and conditions of sale.

Related products

No results message:
Displayed when filters returns no results.

We couldn't find any items that match your criteria.

Please try a different keyword.

Service unavailable:
Displayed when filter service cannot be reached.

Sorry, this service is currently unavailable.

Please try again later.

Get in touch

Have a question for our team?

Ask about our equipment solutions, ranging from Macquarie equipment inventory sales, sourcing programs, surplus disposition options, and direct equipment purchases.

I agree to receive further communication from Macquarie Group Limited in accordance with its Privacy Policy, as amended from time to time.