Macquarie Semiconductor and Technology on behalf of Micron Technology Taiwan, Inc. (F11)

Applied Materials (AMAT) Endura II Front-End Metallization

Asset ID: 171911

Print spec sheet

Applied Materials (AMAT)

Endura II Front-End Metallization

PVD (Physical Vapor Deposition)

Deposition Equipment

Equipment details:

Date of Manufacture:

Currently Configured for: 300mm

Current Equipment Status: Available

Asset HDD not included

Location of Equipment: Taoyuan, Taiwan

Available date: Currently Available


Tool config is based on original PO, please verify tool details at tool inspection


Process: 100s 55 BDL

Software Version: CPCI B50140

System Power Rating: 208 AC 3-Phase +480V Noraml

Loading Configuration: 3 load port


Chm Position 2:Cobalt; Chemicals/ Gases Used: N2,Ar

Chm Position 3:Cobalt; Chemicals/ Gases Used: N2,Ar

Chm Position 4:SIP; Chemicals/ Gases Used: N2,Ar

Chm Position 5:Cobalt; Chemicals/ Gases Used: N2,Ar

Chm Position C:PCXT; Chemicals/ Gases Used: N2,Ar


Chamber position: C,D

Process Type: Reactive PC

Shutter option: none

chamber body (Al or SST): Al

chamber body part number: 0040-76718

Slit valve seal (bonded or o-ring): bonded

Slit Valve door part number: 0040-84391

Target vendor: n/a

Target No.: n/a

Bakeout/idle power (%): n/a

E-Mag Power Supply: n/a

E-Mag Supply Vendor/Type: n/a

OEM Part Number: n/a

DC Power supply(AE-MDX????): n/a

AMAT Part number Master: n/a

OEM Part Number Master: n/a

AMAT Part number Slave: n/a

OEM Part Number Slave: n/a

Generator Size : n/a

Total DC (12 kwh,24kwh, etc): n/a

Bias Generator : n/a

AMAT Part number : n/a

OEM Part Number: n/a

Bias Generator Size: n/a

Bias Generator Frequency: 13.56MHz and 2MHz(in one generator)

Rf coil generator: COMDEL CDX-2000

AMAT Part number : 0190-23308

OEM Part Number: n/a

DC Coil Power Supply: n/a

AMAT Part Number: n/a

OEM Part Number: n/a

Magnet rotation speed (rpm): n/a

Magnet shim thickness: n/a

Magnet type: n/a

Magnet part number: n/a

Magnet Serial Number (man. Date): n/a

Target to magnet spacing(mm): n/a

adaptor p/n: n/a

Kit spacer upper p/n: n/a

Kit spacer lower p/n: n/a

upper shield p/n: Belljar 0040-55456

Treatment (Arc spray/Bead Blast): Al2O3

Treatment roughness (RA): n/a

lower shield p/n: 0040-86514

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

inner(or mid) shield p/n: 0021-19342

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

shield clamp p/n: 0020-19258

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

inner(or mid) shield clamp p/n: Insulator 0200-01903

Treatment (Arc spray/Bead Blast): Al2O3

Treatment roughness (RA): n/a

lower shield clamp p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

pedestal cover p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

dep ring p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

cover ring p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

insulator bushing p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

Shutter: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

pedestal type: n/a

pedestal p/n: n/a

heater spacing in mm: n/a

heater spacing in steps: n/a

min heater spacing in mm: n/a

min heater spacing in steps: n/a

max heater spacing in mm: n/a

max heater spacing in steps: n/a

Lift fingers p/n: n/a

Lift hoop p/n: n/a

Cryo restrictor(Y/N): n/a

Cryo restrictor Part Number: n/a

Max Cryo regen gas load (L): n/a

Cryo gate valve (2/3 pos): Pendulum

MFC 1 Gas: He

MFC 1 Cal Factor: 1

MFC 1 Size: 300

MFC 1 Type: He

MFC 1 Part Number: 0010-44160

MFC 2 Gas: Ar2

MFC 2 Cal Factor: 1

MFC 2 Size: 200

MFC 2 Type: Ar

MFC 2 Part Number: 3030-13113

MFC 3 Gas: Ar

MFC 3 Cal Factor: 1

MFC 3 Size: 20

MFC 3 Type: Ar

MFC 3 Part Number: 3030-13116

MFC 4 Gas: (MFC6) H2

MFC 4 Cal Factor: (MFC6) 1

MFC 4 Size: (MFC6) 100

MFC 4 Type: (MFC6) H2

MFC 4 Part Number: (MFC6) 0015-02990

Chamber base pressure (T): 0.0000002

Chamber Rate-of-Rise(nTorr/min): 15000

Press. and ROR at Startup: not necessary

Pressure Rise 1 min: not necessary

Pressure Rise 5 min: not necessary

Pressure Rise 10 min: not necessary

Pressure vs. Gas Flow table: not necessary

Process Ar Supply Pressure: 34.7

Process N2 Supply Pressure: 33.9

Cryo Regen N2 pressure: na

Vent Ar pressure: 47.7

Optional Gas (He): 30.1

O2 (Ch. F): n/a

H2(Ch. E): n/a

H2(Ch. C): n/a

CDA: 95.7

SLIT VALVE CDA: 85

Cooling Water Flow (GPM): 0.8


Chamber position: 4

Process Type: SIP Ti

Shutter option: yes

chamber body (Al or SST): 

chamber body part number: 0040-98657

Slit valve seal (bonded or o-ring): Bonded

Slit Valve door part number: 0040-84391

Target vendor: Nikko/Tosoh

Target No.: TAG73

Bakeout/idle power (%): 40

E-Mag Power Supply: na

E-Mag Supply Vendor/Type: na

OEM Part Number: na

DC Power supply(AE-MDX????): AE-Pinnacle

AMAT Part number Master: 0190-08122

OEM Part Number Master: na

AMAT Part number Slave: 0190-08122

OEM Part Number Slave: na

Generator Size : 20kw

Total DC (12 kwh,24kwh, etc): 40kw

Bias Generator : ENI - GHW12Z

AMAT Part number : 0190-25529

OEM Part Number: na

Bias Generator Size: 1250w

Bias Generator Frequency: 13.56 Mhz

Rf coil generator: na

AMAT Part number : na

OEM Part Number: na

DC Coil Power Supply: na

AMAT Part Number: na

OEM Part Number: na

Magnet rotation speed (rpm): n/a

Magnet shim thickness: 65

Magnet type: SIP

Magnet part number: 0010-11228

Magnet Serial Number (man. Date): no need

Target to magnet spacing(mm): 1.5mm

adaptor p/n: 0040-82921

Kit spacer upper p/n: 0040-76943

Kit spacer lower p/n: 0040-62877

upper shield p/n: 0020-23549

Treatment (Arc spray/Bead Blast): Arc Spray

Treatment roughness (RA): na

lower shield p/n: 0020-02344

Treatment (Arc spray/Bead Blast): Arc Spray

Treatment roughness (RA): na

inner(or mid) shield p/n: 0020-54777

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): na

shield clamp p/n: na

Treatment (Arc spray/Bead Blast): na

Treatment roughness (RA): na

inner(or mid) shield clamp p/n: 0020-08299

Treatment (Arc spray/Bead Blast): Arc Spray

Treatment roughness (RA): na

lower shield clamp p/n: 0020-02348

Treatment (Arc spray/Bead Blast): Arc Spray

Treatment roughness (RA): na

pedestal cover p/n: na

Treatment (Arc spray/Bead Blast): na

Treatment roughness (RA): na

dep ring p/n: 0200-02916

Treatment (Arc spray/Bead Blast): na

Treatment roughness (RA): na

cover ring p/n: 0021-17770

Treatment (Arc spray/Bead Blast): Arc Spray

Treatment roughness (RA): na

insulator bushing p/n: 0200-00590

Treatment (Arc spray/Bead Blast): na

Treatment roughness (RA): na

Shutter: 0021-25014

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): na

pedestal type: FDR SLT

pedestal p/n: 0010-22985

heater spacing in mm: no concern

heater spacing in steps: -55050

min heater spacing in mm: no concern

min heater spacing in steps: no concern

max heater spacing in mm: no concern

max heater spacing in steps: no concern

Lift fingers p/n: no concern

Lift hoop p/n: no concern

Cryo restrictor(Y/N): na

Cryo restrictor Part Number: na

Max Cryo regen gas load (L): 400

Cryo gate valve (2/3 pos): na

MFC 1 Gas: N2

MFC 1 Cal Factor: na

MFC 1 Size: 50

MFC 1 Type: na

MFC 1 Part Number: na

MFC 2 Gas: na

MFC 2 Cal Factor: na

MFC 2 Size: na

MFC 2 Type: na

MFC 2 Part Number: na

MFC 3 Gas: Ar

MFC 3 Cal Factor: na

MFC 3 Size: 50

MFC 3 Type: na

MFC 3 Part Number: na

MFC 4 Gas: ArH

MFC 4 Cal Factor: na

MFC 4 Size: 10

MFC 4 Type: na

MFC 4 Part Number: na

Chamber base pressure (T): 2.0 e-8

Chamber Rate-of-Rise(nTorr/min): 522

Press. and ROR at Startup: no concern

Pressure Rise 1 min: no concern

Pressure Rise 5 min: no concern

Pressure Rise 10 min: no concern

Pressure vs. Gas Flow table: no concern

Process Ar Supply Pressure: 30

Process N2 Supply Pressure: 30

Cryo Regen N2 pressure: 90

Vent Ar pressure: 40

Optional Gas (He): na

O2 (Ch. F): na

H2(Ch. E): na

H2(Ch. C): na

CDA: 88

SLIT VALVE CDA: 82

Cooling Water Flow (GPM): 8.9


Chamber position: 2,3,5

Shutter option: yes

chamber body (Al or SST): SST

chamber body part number: 0040-98657

Slit valve seal (bonded or o-ring): bonded

Slit Valve door part number: 0040-84391

Target vendor: NIKKO

Target No.: TAG169

Bakeout/idle power (%): n/a

E-Mag Power Supply: n/a

E-Mag Supply Vendor/Type: n/a

OEM Part Number: n/a

DC Power supply(AE-MDX????): MKS

AMAT Part number Master: 0190-23736

OEM Part Number Master: n/a

AMAT Part number Slave: n/a

OEM Part Number Slave: n/a

Generator Size : 10kw

Total DC (12 kwh,24kwh, etc): 10kw

Bias Generator : n/a

AMAT Part number : n/a

OEM Part Number: n/a

Bias Generator Size: n/a

Bias Generator Frequency: n/a

Rf coil generator: n/a

AMAT Part number : n/a

OEM Part Number: n/a

DC Coil Power Supply: n/a

AMAT Part Number: n/a

OEM Part Number: n/a

Magnet rotation speed (rpm): 55

Magnet shim thickness: CH2: 1.0mm CH3: 1.0mm CH5: 1.0mm

Magnet type: ALPS CO

Magnet part number: 0010-51232

Magnet Serial Number (man. Date): no concern

Target to magnet spacing(mm): CH2 1.345 mm; CH3 1.3425 mm; CH5 1.2 mm

adaptor p/n: 0240-29326 KIT, ADAPTER, ALPS CO, 300MM ENDURA BLUE adapter:0040-62882

Kit spacer upper p/n: n/a

Kit spacer lower p/n: n/a

upper shield p/n: DARK SPACE SHIELD 0021-18068

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

lower shield p/n: 0020-48185

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

inner(or mid) shield p/n: 0040-76737 (Ground ring)

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

shield clamp p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

inner(or mid) shield clamp p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

lower shield clamp p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

pedestal cover p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

dep ring p/n: 0200-20437

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

cover ring p/n: 0021-22177

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

insulator bushing p/n: n/a

Treatment (Arc spray/Bead Blast): n/a

Treatment roughness (RA): n/a

Shutter: 0021-26565

Treatment (Arc spray/Bead Blast): Bead Blast

Treatment roughness (RA): n/a

pedestal type: HT-ESC

pedestal p/n: 0010-27430

heater spacing in mm: 238

heater spacing in steps: CH2 step: -55340; CH3 step: -55230; CH5 step: -55160

min heater spacing in mm: No Data

min heater spacing in steps: CH2 Lower limit -52200; CH3 Lower limit -52100; CH5 Lower limit -52800

max heater spacing in mm: No Data

max heater spacing in steps: CH2 Upper limit -70000 CH3 Upper limit-70000 ; CH5 Upper limit -72500

Lift fingers p/n: 0020-46828

Lift hoop p/n: 0020-75465

Cryo restrictor(Y/N): n/a

Cryo restrictor Part Number: n/a

Max Cryo regen gas load (L): n/a

Cryo gate valve (2/3 pos): 3 Position

MFC 1 Gas: AR

MFC 1 Cal Factor: n/a

MFC 1 Size: 100

MFC 1 Type: AR

MFC 1 Part Number: Brooks (can not see P/N)

MFC 2 Gas: AR

MFC 2 Cal Factor: n/a

MFC 2 Size: 20

MFC 2 Type: AR

"MFC 2 Part Number: Brooks

0010-42843"

MFC 3 Gas: n/a

MFC 3 Cal Factor: n/a

MFC 3 Size: n/a

MFC 3 Type: n/a

MFC 3 Part Number: n/a

MFC 4 Gas: n/a

MFC 4 Cal Factor: n/a

MFC 4 Size: n/a

MFC 4 Type: n/a

MFC 4 Part Number: n/a

Chamber base pressure (T): 5.00E-8 Torr

Chamber Rate-of-Rise(nTorr/min): 2000nTorr/min

Press. and ROR at Startup: Ch2/3/5:Press:2.20E-08Torr  ROR:2xx nT/min

Pressure Rise 1 min: not necessary

Pressure Rise 5 min: not necessary

Pressure Rise 10 min: not necessary

Pressure vs. Gas Flow table: not necessary

Process Ar Supply Pressure: 32psi

Process N2 Supply Pressure: n/a

Cryo Regen N2 pressure: 78

Vent Ar pressure: n/a

Optional Gas (He): n/a

O2 (Ch. F): n/a

H2(Ch. E): n/a

H2(Ch. C): n/a

CDA: 78

SLIT VALVE CDA: 77

Cooling Water Flow (GPM): CH2:8 CH3:10 CH5:11


Damage/Missing parts list

Please inspect tool to reconfirm

Dry pumps and customer provided items not included on sales


Enquire about this product

I agree to receive further communication from Macquarie Group Limited in accordance with its Privacy Policy, as amended from time to time.

Product Images

The information referenced on this page is accurate to the best of our knowledge. We do not warrant the completeness or accuracy of the information contained herein. Interested parties are encouraged to request inspection to verify equipment condition, configuration, and completeness. Any offer to purchase equipment shall be subject to our standard terms and conditions of sale.


Related products

No results message:
Displayed when filters returns no results.

We couldn't find any items that match your criteria.

Please try a different keyword.

Service unavailable:
Displayed when filter service cannot be reached.

Sorry, this service is currently unavailable.

Please try again later.

Get in touch

Have a question for our team?

Ask about our equipment solutions, ranging from Macquarie equipment inventory sales, sourcing programs, surplus disposition options, and direct equipment purchases.

I agree to receive further communication from Macquarie Group Limited in accordance with its Privacy Policy, as amended from time to time.